Spirea "Gold fontaine": description, planting, care and reproduction

Spirea "Gold Fontane" in most cases is used to form bouquets and wedding decor due to its original appearance. It has small flowers that run along long stems.

If there is a desire to use this flower as a garden decoration, then a lot of space is needed for it, because individual spirea bushes can reach three meters in height and 7 meters in width.

The culture was obtained by crossing its two species, Spiraea cantoniensis and Spiraea trilobata. Spirea is a voluminous vase-shaped shrub with long cascading stems.

The plant is pleasing to the eye throughout the summer. A scattering of small flowers with a diameter of no more than 10 mm are collected in umbrellas. Spirea was liked by many gardeners for its flowers, which appear as the leaves bloom.

The crop is planted in the spring. The successful flowering of the spirea in the future depends on how it will be produced.

To begin with, a place is sought for the growth of the bush. It should be well lit.

The culture is undemanding to the state of the soil - it can grow on both acidic and alkaline soils. Although moisture is preferable, it can withstand dry periods. Drainage of the area should also be ensured.

Most plants of this type can grow in low light, only in this case the flowering activity will be reduced, and the leaves will become lethargic. For those spirits that grow in the apartment, additional lighting should be done.

It must be remembered that not all varieties of Wangutta spirea can endure a long period in direct sunlight: some bloom and are filled with strength from the sun's rays, while others, on the contrary, fade. And also plants can get serious burns to the leaves.

Before planting for the spirea, a hole should be dug, which should be twice as wide as an earthen lump on the roots. Compost is placed in the resulting hole, filling it with 50% of the depression, the remaining 50% is soil. You can mix the soil with compost well using the most ordinary shovel. The root system is spread in the middle of the formed hole and covered with compost.

Spirea care consists of several stages. When there is no desire to fight weeds and water often, it is necessary to mulch in the hole. This procedure can solve a number of problems.

It is necessary to water the plantings once a week, especially in dry summers.

To provide the culture with all useful substances, 1 cm of compost should be added annually in the spring. As a top dressing, phosphorus is well suited, stimulating intensive root formation. It is introduced during planting and during the first growing season.

In most cases, when the plant is planted, a water ring is made, which is a mound of dense earth. This procedure helps direct moisture to the outer edges of the planting hole, and also stimulates the emergence of new shoots on the surface.

Another layer of mulch on the ring will prevent damage and accumulate liquid after watering.

Pruning should be done in summer or autumn. Removal of all dead and damaged stems is carried out using a well-sharpened knife or scissors. The remaining branches are cut so that the required height and width are obtained.

To the main advantages of this variety include:

• unpretentiousness to the soil where it grows;
• frost resistance;
• blooms already at the end of spring.

Spirea Wangutta is used to form hedges, as well as in combination with other flowers and singly. Looks good along the water's edge and next to stone paths.

Spirea "Gold Fontaine" is resistant to frost, therefore, it is not necessary to cover it for the winter period. There are cases when an uncovered bush tolerated temperatures down to -35 degrees Celsius.

Spirea is covered only in the northern regions of the country, where the temperature drops below -40 degrees Celsius. There, the area at the roots of the shrub is covered with fallen dry foliage, film or covering material so that the culture will survive frosts. If frozen shoots are found in the spring, then they must be removed so that the plant does not waste its vitality on them.

However, during the first wintering, young bushes should be covered so that they can fully take root and are not affected by the cold.

Spirea reproduction process happens in several ways:

• cuttings;

• layering;

• division.

Cuttings can be cut 2 weeks after flowering. They are long lignified shoots. However, they should not have any damage. In order for the roots to appear, the cuttings are placed in a container with a substrate of equal proportions of peat and river sand. Next year, cuttings with emerging roots can be planted in open ground.

Reproduction by layering is the easiest and most common way that anyone, even a novice gardener, can use. DFor the reproduction of spirea in this way, the lignified shoot closest to the soil is needed. It must be placed in the recess so that the top sticks out a couple of centimeters. Layers must be attached to the soil with a hairpin and sprinkled with soil with nutrients. Such shoots are watered, and covered with foliage or film for the winter. In the spring, a branch that has taken root must be separated from the shrub and planted in a new place.

Can be propagated by spirea by dividing the main bush during transplantation. Here you can divide one large bush into several small ones. The main condition is the presence of healthy shoots. It is necessary to divide the spirea carefully so as not to harm the root system.

For a brief overview of the Gold Fontaine spirea, see the video below.