Error F01 on the Indesit washing machine: causes and tips for elimination

An error with the F01 code on a washing machine of the Indesit brand is infrequent. Usually it is characteristic of equipment that has been in operation for a long time. This breakdown is very dangerous, as delaying repairs can create a potentially fire hazardous situation.

What this error means, why it appears and how to fix it, and will be discussed in our article.

If an error with information code F01 is displayed on the Indesit washing machine for the first time, then you must immediately take measures to eliminate it. This coding indicates that a short circuit has occurred in the electrical circuit of the engine. In other words, the breakdown concerns the motor wiring. As you know, the engine in washing machines breaks down in most cases with wear, which is why the problem is most typical for old equipment.

Washing machines manufactured before 2000 work based on the EVO control system - in this series there is no display showing error codes. You can determine the problem in them by the blinking of the indicator - its lamp blinks several times, then interrupts for a short time and repeats the action again. In machines of the Indesit brand, a malfunction with the motor wiring is signaled by an indicator that indicates the "additional rinse" or "spin" mode. In addition to this "illumination", you will surely notice the rapid blinking of the "stacker" LED, which directly indicates the blocking of the window.

The latest models are equipped with an EVO-II control system, which is equipped with an electronic display - it is on it that the information error code is displayed in the form of a set of letters and numbers F01. After that, deciphering the source of the problems will not be difficult.

The error makes itself felt in the event of a breakdown of the electric motor of the unit. In this case, the control module does not transmit a signal to the drum, as a result, the rotation is not carried out - the system remains stationary and stops working. In this position, the washing machine does not respond to any commands, does not turn the drum and, accordingly, does not start the washing process.

The reasons for such an error in a washing machine of the Indesit brand can be:

• failure of the power cord of the machine or a malfunction of the outlet;
• interruptions in the functioning of the washing machine;
• frequent switching on and off during the washing process;
• power surges in the network;
• wear of the brushes of the collector motor;
• the appearance of rust on the contacts of the engine block;
• breakdown of the triac on the control unit CMA Indesit.

Before proceeding with the elimination of the breakdown, it is necessary to check the voltage level in the network - it must correspond to 220V. If there are frequent power surges, then first connect the machine to the stabilizer, in this way you can not only diagnose the operation of the unit, but also further extend the operating period of your equipment many times, protect it from short circuits.

If, after a restart, the error code continues to be displayed on the monitor, you need to start troubleshooting. First, make sure the outlet and power cord are intact.In order to make the necessary measurements, you need to arm yourself with a multimeter - with the help of this device, it will not be difficult to find a breakdown. If the external monitoring of the machine did not give an idea of ​​the cause of the breakdown, then it is necessary to proceed with an internal inspection. To do this, you will have to get to the engine by following these steps:

• open a special service hatch - it is available in every Indesit CMA;
• supporting the drive strap with one hand and rotating the second pulley, remove this element from the small and large pulley;
• carefully disconnect the electric motor from its holders, for this you need an 8 mm wrench;
• disconnect all wires from the motor and remove the device from the SMA;
• on the engine you will see a couple of plates - these are the carbon brushes, which must also be unscrewed and carefully removed;
• If during visual inspection you notice that these bristles are worn out, you will have to replace them with new ones.

After that, you need to put the machine back together and start the wash in test mode. Most likely, after such a repair, you will hear a slight crackle - you should not be afraid of this, so the new brushes rub in... After several wash cycles, extraneous sounds will disappear.

If the problem is not in the carbon brushes, then you need to make sure the integrity and insulation of the wiring from the control unit to the motor. All contacts must be in good working order. In high humidity conditions, they can corrode. If rust is found, it is necessary to clean or completely replace parts.

The motor can be damaged if the winding burns out. Such a breakdown requires quite expensive repairs, the cost of which is comparable to buying a new motor, so most often users either change the entire engine or even purchase a new washing machine.

Any work with wiring requires special skills and knowledge of safety precautions, therefore, in any case, it is better to entrust this matter to a professional who has experience in such work. In such a situation, it is not enough to be able to handle a soldering iron, it is possible that you will have to deal with reprogramming new boards. Self-analysis and repair of equipment makes sense only if you are repairing the unit in order to acquire new skills. Remember, the motor is one of the most expensive parts of any SMA.

How to repair electronics, see below.