DIY paper towel holder: types and master class

Paper towels are firmly established in many kitchens. They are convenient for wiping dirt on work surfaces, removing moisture from wet hands. They don't need to be washed after cleaning, unlike regular kitchen towels.

There are two types of paper towels:

• sheet with a dispenser (used in restaurants and shopping centers);
• rolls of a certain width, may not have a sleeve (applicable for home use).

Density and number of layers are the main factors showing quality that affect the price of a product.

There can be three options:

• single-layer (the cheapest and thinnest option);
• two-layer (denser than the previous ones);
• three-layer (the densest, with the greatest absorption).

Color and texture solutions can be varied (from classic white to various ornaments). They can have an absolutely smooth surface or a relief pattern. It is not very convenient when a roll of towels is in a drawer or on a shelf. In this case, the paper towel holder comes to the rescue.

There are many options for making a wall-mounted dispenser.

The easiest option is considered to be a hanger. To implement it, you need to take a hanger, preferably plastic or metal.

Then you can act in two ways:

• unbend and put on a roll with a towel;
• cut in half the lower part of the trempel and, slightly bending the halves, string a roll on them.

Decorating can be done at your own discretion. You can wrap the hangers with a decorative cord, braid, lace.

The wall-mounted version of the paper towel holder can be made from old beads or using large decorative beads strung on a string or elastic band. To do this, you need to thread the beads through the roll sleeve and fix them on the wall. This option looks stylish and modern.

Another option for a wall mounted towel holder can be made with leather straps.

To do this, you will need the following items:

• awl;
• leather straps in the amount of two pieces;
• wood rod;
• metal rivets and accessories.

First you need to make 5 holes in each strap. To do this, each of them must be folded in half and make 2 through punctures at a distance of 5 and 18 cm from the edge. In one half, an additional hole must be made at a distance of 7.5 cm from the end of the strap. Then you need to install the rivet in the aligned holes, which were made at a distance of 18 cm.

It is necessary to mount on the wall. For this purpose, you can use a screw or a suction cup, which should be installed in the holes made at a distance of 7.5 cm from the edge. They must be attached along a strictly horizontal line at a distance of 45 cm from each other. After that, you should use the last rivets for holes 5 cm from the edge. The last step is to thread a wooden rod into the bushing of the roll, thread its ends through the loops in the straps.

With the help of scraps of copper pipes, you can make the kitchen more convenient, as well as save space.

You will need:

• copper fittings (tube, 2 corners and a cap);
• metal circle for fastening with a hole in the center equal to the pipe diameter and 4 screw holes;
• Super glue.

First you need to measure a tube 2 cm longer than the roll length and another about 10 cm long. The second piece is needed to fix it under the kitchen cabinet. Don't make it too long so that the towels don't hang too low. We must not forget that the installation will add a couple more centimeters.

Next, you need to fasten the tubes together using a corner and superglue, which should be applied to the inner side of the corner. Then, a second corner and cap must be attached to the other end of the long tube. Do not forget that the cap with the angle must be parallel to the short tube.

The third step is to secure the short tube in the metal circle. The last step is to attach the entire structure under the kitchen cabinet using self-tapping screws, Velcro or suction cups. Next, you can put on a roll with a towel.

This option will appeal to fans of eco-style.

You will need:

• newspaper tubes;
• hot glue or PVA;
• cardboard;
• elastic.

Take 12 tubes and tighten them about in the middle with a clerical rubber band. The tubes on one side must be wrapped perpendicularly. The resulting base can be placed on the table on the tubes bent in a circle. Next, you need to weave 6 rows with "string". Then 5 more rows, adding one stick each time. This will be the basis. The working tubes must be cut and glued.

The rod also needs to be braided. To do this, remove the gum, grease with glue and braid the second half of the sticks. On this basis, it is considered complete.

Three circles with a diameter of a woven base need to be cut out of cardboard.

Next, you need to weave another bottom, for the base of which you will need 24 tubes arranged in a circle. In this way, you need to weave 13 rows. After that, the main tubes must be fixed together and placed perpendicular to the woven bottom. They take 3 tubes and braid the bottom with a string, like a basket.

Then you need to glue cardboard circles with the resulting basket. To do this, use PVA glue. Weave 3 more rows with a string and attach the first part. Then, on 13 racks, you can weave a "half-wall". To do this, each row starting on the right must be made shorter than the previous one, removing one of the racks from the base (and so on to the end).

The last step is to cut off all unnecessary parts, securing them with a "string". The finished product must be abundantly coated with PVA glue.

For another interesting master class on creating a paper towel holder, see below.