Voltage stabilizers for TV: varieties, selection and connection

Content
  1. What is it needed for?
  2. Views
  3. Comparison with a surge protector
  4. How to choose?
  5. How to connect?

It is no secret that the voltage in the power grid in small towns and suburbs often jumps and ranges from 90 to 300 V. This is due to the fact that power lines fail due to wear, they are confused by the wind and falling branches. Also, they are not designed for such a load that modern technology gives. Air conditioners, welding machines, microwave ovens put a heavy load on power lines and can cause a sharp drop in voltage. To avoid malfunction of home appliances and its stable operation, voltage stabilizers are used.

What is it needed for?

TV stabilizer - This is a device that allows you to protect equipment from a sharp drop and overvoltage in the network. For normal operation of the TV, a voltage of 230 to 240 V is required. Excess or a sharp drop in voltage can negatively affect the equipment and take it out of order. Stabilizers, depending on the model, help raise the voltage to the required value or reduce it. Thanks to them, your TV will work in the desired voltage range, which means that its service life will increase.

Views

Among the wide range of stabilizers, you can choose any model of different prices. They all differ in their principle of operation, design and other characteristics. By the principle of operation, devices can be divided into electronic, electromechanical, relay, ferroresonant and inverter models.

  • Step or relay models differ in that their operation is based on switching the windings of the working transformer. When the input voltage changes, the electromagnetic relay closes, the quality of the sinusoidal voltage decreases. The voltage adjustment in such models occurs abruptly with the accompaniment of sound, since the relay contacts are closed. The most common failure in such devices is a sticking relay.

This is mainly in cases where voltage surges are very frequent with a large difference in volts. Such devices have the lowest cost.

  • Electronic. In such designs, the switching of the autotransformer windings occurs using triac or thyristor switches. The devices have a fairly high cost, due to their silent operation and instantaneous regulation of the output voltage indicators.
  • Electromechanical. Such devices are called servo-motor or servo-driven. The voltage is adjusted by moving the carbon contacts along the transformer windings using an electric drive. Such stabilizers are inexpensive. Their voltage regulation is very smooth, they do not take up much space due to their small size. Among the disadvantages are noise in operation and poor performance.
  • Ferroresonant models. Such devices are distinguished by a long service life, low cost, and precise adjustments of the output parameters. Are heavy and noisy during operation.
  • Inverter. Stabilizer types convert voltage in a double way. Initially, the input voltage changes to constant, and then goes to alternating. In such devices, absolutely silent operation is noted. They are reliably protected from external interference and power surges. These types have the highest cost of all provided above.

Comparison with a surge protector

An option to prevent breakdowns of TVs due to power surges can be a surge protector. It looks like a regular power strip, but a special filter board is installed inside its structure. It can be of several types.

  • Varistors. At very high voltages, they give their resistance and take on the entire load, thereby short-circuiting the circuit. Because of this, they usually burn out, but the equipment remains protected, that is, this is a one-time option for overvoltage protection.
  • LC filter absorbs high-frequency interference thanks to a circuit of capacitor coils and inductors. Thermal fuses can be reusable and fusible. They have a special button on the body. When the voltage exceeds the permissible rate, the fuse releases the button and breaks the circuit. It works automatically. To return the filter to normal operating mode, simply press the button back.
  • Gas dischargers. Sometimes gas discharge electrodes are installed in the filter design along with a varistor. It is they who take on the voltage and quickly eliminate the potential difference.
  • All surge protectors are grounded. The responsible manufacturer will specify in the instructions for which lines the varistor protection is provided. If the varistor is provided only between ground and phase, then grounding is necessary for such a filter. Grounding is not required only if phase-to-zero protection is specified.
  • Network filter Is a rather complex device that includes electronic components for the best suppression of impulse noise and prevents equipment from short circuits and overloads. Therefore, we can definitely say that stabilizers are much better than surge protectors.

After all, the filter is intended only for adjusting high frequency noise and impulse noise. They are unable to deal with strong and prolonged swings.

How to choose?

To select the required stabilizer model for your TV, you must first of all understand how strong the voltage drops in your network are. Since all stabilizers have different powers, you should understand that the model of the stabilized device also depends on the power of your TV. In any case, you must determine the wattage of your TV. These indicators are in his data sheet. Based on this, it is possible to select a stabilizing device in terms of power.

If you live in a rural area, then consider such an indicator as short circuit protection... Indeed, in strong winds, power lines can be closed.

Among the selection criteria, the noise level of the device during its operation is essential. After all, if you install the stabilizer in a recreation area, then its loud operation will give you discomfort. More expensive models are quieter.

If you want to connect the stabilizer not only to a TV, but also to other devices, for example, a home theater, then the total power of the devices must be taken into account.

An indicator such as accuracy plays an important role for a TV, since the quality of the picture and sound depends on it. Therefore, when choosing a model, you need to pay attention to models with this indicator no more than 5%.

If in your region the input voltage is from 90 V, then the model of the stabilized device must also be purchased with a range of 90 V.

The dimensions of the device are also of great importance, since the compact dimensions do not take up much space and do not attract attention.

If you have already decided on the parameters of the stabilizer you need, now it is important to decide on the manufacturer. Now there are a lot of worthy companies that are engaged in the release of this product. Russian manufacturers offer high-quality devices at a fairly affordable cost. Chinese brands have the lowest price, but also the most non-guaranteed quality.European companies offer products several times more expensive than their Chinese and Russian counterparts, but the quality of the goods is high. Of course, modern TV models have a built-in stabilizer, which cannot always protect against large power surges. That's why you have to purchase independent equipment.

How to connect?

Connecting the stabilizer to the TV is a fairly simple procedure that does not require special skills and knowledge. There are 5 connectors on the back of the device, which are usually located the same in all models, from left to right. This is the input phase and zero, grounding zero and the phase going to the place of the load. The connection must be carried out with the power supply disconnected. It is necessary to install an additional RCD in front of the meter in order to prolong the operation of the stabilizer. An earthing loop must be provided in the electrical network.

The stabilizer cannot be installed immediately in front of the meter... If its power is less than 5 kW, then connection is possible directly to the outlet. The stabilizer is installed about half a meter from the TV set, but not closer, since the influence of stray fields from the stabilizer is possible, and this can negatively affect the quality of the TV. To connect, you need to insert the TV plug into the stabilizer socket called "output". Then turn on the TV with the remote control or using the button. Next, insert the plug from the stabilizer into a power outlet and turn on the switch. After the stabilizer is connected to the TV, turning on and off the TV must be done only from the stabilization device.

For a voltage regulator for a TV, see the video below.

no comments

The comment was sent successfully.

Kitchen

Bedroom

Furniture