How to make a sandblast from a fire extinguisher with your own hands?

Content
  1. Device
  2. Tools and materials
  3. Manufacturing instruction

Very often, in certain areas of human activity, there is a need for quick and high-quality cleaning of various surfaces from contamination or glass matting. This is especially in demand in small car workshops or private garages. Unfortunately, specialized equipment for this has a very high price.

In the same time, if you have a powerful compressor at hand, then you can easily make a homemade sandblaster. Let's try to figure out how to make such a device with our own hands quickly and as simply as possible.

Device

First, you should consider what components the sandblast consists of in order to clearly understand how to make it.

Regardless of the scheme of the device, the sandblast must have a common flow of abrasive and outgoing air. If the assembly is carried out according to the pressure-type scheme, then the sand, due to the application of pressure, will fall into the outlet type pipe, where it will be mixed with the air supplied by the compressor. To create a vacuum in the abrasive feed channel, the so-called Bernoulli effect is applied.

The supply of sand to the mixing area is carried out exclusively under the influence of atmospheric pressure.

The ability to make sandblasting from a fire extinguisher or other improvised means in various ways is explained by the fact that you can use a lot of things and materials that, at first glance, seem unnecessary.

A homemade version is made on the basis of typical schemes, which may differ from each other only in the method of feeding sand to the part to be cleaned. But whatever the diagrams (drawing) of the device, they will all include the following elements:

  • a compressor that will pump the air mass;
  • a gun, with the help of which the abrasive composition will be supplied to the surface requiring cleaning;
  • hoses;
  • abrasive storage tank;
  • the receiver will be required to form the required supply of oxygen.

To increase the time of continuous use of the equipment, to maintain the pressure required for high-quality operation, a moisture separator should be installed.

If a plunger-type compressor is used, then a mechanism should be installed on the air channel responsible for the intake, which will filter the oil.

Tools and materials

To obtain a sandblaster from a fire extinguisher, you will need to have the following tools and spare parts on hand:

  • a pair of ball valves;
  • capacity from a fire extinguisher, a cylinder from under gas or freon;
  • a pair of tees;
  • part of the pipe for the formation of a funnel for filling the abrasive;
  • hoses with an internal size of 1 and 1.4 centimeters, designed to release the abrasive and supply air from the compressor;
  • clamps with fittings used to secure hoses;
  • fum tape of sanitary type, the use of which allows the connection of structural parts of the assembled model.

Manufacturing instruction

Now let's move on to considering the direct process of creating a sandblasting apparatus from a fire extinguisher. It is carried out as follows:

  1. Preparing the camera. To prepare the chamber for further work, gas must be released from the fire extinguisher or powder must be poured out. If the cylinder was pressurized, then all contents will need to be removed from it.
  2. Holes will need to be made in the container. In the upper part, the holes will serve for filling in the abrasives. They should be the same size as the diameter of the fitted tube. And from below, holes are made for the subsequent fastening of the crane by welding.
  3. Now the valve is being welded into the cylinder, which will be responsible for adjusting the supply of abrasive materials. In this case, you can use an alternative option - mount an adapter where the regulator will be screwed.
  4. After the tap, you should install the tee, as well as the mixing unit. For their high-quality fixing, you will need to use fum tape.
  5. At the last stage, a valve should be installed on the cylinder valve., and after it mount the tee.

Now you need to complete the assembly of the main structure by welding the handles for transporting equipment or installing wheels.

It will not be superfluous to equip the sandblast from a fire extinguisher and legs, which will be supports. This will make the structure as stable as possible.

After that, connections are created, as well as feed and discharge paths for the finished mixture:

  • fittings are installed on the balloon valve and tee located below;
  • the hose, which has a diameter of 1.4 centimeters and is intended for air supply, is placed between the valve tee and the corresponding mixing unit, which is located at the bottom of the container;
  • a compressor must be connected to the inlet of a valve tee equipped with a fitting that remains free;
  • the remaining branch of the tee, from the bottom, is connected to a hose through which the abrasive will be supplied.

On this, the formation of sandblasting can be considered complete.

Now you need to create a gun and a nozzle. The first element is easy to create using a ball valve attachment, which is mounted at the end of the air-abrasive compound supply hose. Such a device of the outlet type is, in fact, a clamping nut, with the help of which the nozzle is fixed to remove the mixture.

But the nozzle can be made metal by turning it on a lathe. A more convenient solution would be to create this element from an automotive spark plug. To do this, you will need to cut the mentioned element with a grinder in such a way that you can separate the strong column made of ceramics from the metal parts of the structure and give it the required length.

It should be said that the process of separating the required part of the candle is very dusty and is accompanied by an unpleasant odor. So it should not be carried out without the use of personal protective equipment.

And if you do not have the skills to work with the mentioned tool and the necessary premises where this process can be performed, then it is better to simply purchase a ceramic nozzle in some store and install it.

Now the device should be checked. To do this, you need to unscrew the plug in the cross, and pour sand into the body with sandblasting. It would be better to use a watering can so as not to spill it. Previously, it must be well sifted and fine-grained.

We activate the compressor, find a suitable pressure, and also adjust the amount of sand that is supplied using the tap at the bottom of the device. If everything is in order, then the resulting construction will work correctly.

In general, it should be noted that homemade sandblasting made from a fire extinguisher is more effective than industrial designs that can be found on the market. That's why it would be better to spend your own time creating a homemade analogue. Moreover, this does not require any large financial investments or resources.

How to make sandblasting from a fire extinguisher with your own hands, see the video below.

no comments

The comment was sent successfully.

Kitchen

Bedroom

Furniture